Compressive strength, building materials, nail gun, driving energy.
Abstract:
Determination of the unconfined compressive strength (UCS) of construction materials in the laboratory is tedious and time-consuming. There have been many attempts to indirectly predict UCS using simpler tools and techniques. One of them is the nail gun. The scope of this investigation is to design a nailer which can be applied all construction materials whose UCS range from 1-100 MPa. In the research, rocks, bricks, and concretes prepared in different cement/sand ratios with different strength ranges were used as materials. The unconfined compressive strength of the materials used in the experiments was first determined by conventional compression tests. The nail penetration depths were determined by conducting experiments on the same materials using a nailer with two different energy levels. An empirical relationship was developed by using nail penetration depths, driving energies, and nail diameters as the independent variables and the UCS determined by the conventional method as the dependent variable. According to the empirical relationship determined by multiple regression analysis, the UCS of building materials can be estimated with significance level of 99% by the nail penetration method. The research also revealed that the UCS of rocks might have a coefficient of variation as high as 30%.
A laboratory-scale investigation on freezing-thawing behavior of some natural stone samples manifactured in Turkey
Authors:
Gökhan EROL, Ozan BAYRAM
ABSTRACT
In the study, the changes in the mechanical properties of the natural stone samples, which had been obtained from different regions of Turkey, before and after the freeze-thaw test were examined. Within the scope of the study, 17 different natural stone samples were used and, after chemical and mineralogical-petrographical properties were determined. Water absorption at atmospheric pressure, real density, porosity, and uniaxial compressive strength tests were performed before and after freezing-thawing. The freezing and thawing test has been performed using TS EN 12371 standard from -12 °C to +20 °C in 56 cycles (2 cycles = 24 hours). After the test, the samples were subjected to uniaxial compressive strength test in order to identify the changes of the compressive strength values. The results of the physical and mechanical tests on these samples were evaluated by grouping according to chemical and mineralogical-petrographical properties of natural stones. It was aimed to determine which natural stone samples are resistant to freeze-thaw, and can be used in external cladding applications according to the findings obtained from the study.
https://doi.org/10.19111/bulletinofmre.746486
Keywords:
Natural stone, Freezing and thawing, Water absorption, Thermalmechanical behavior, Uniaxial compressive strength.
Kamil KAYABALI, Ramin ASADİ, Mustafa FENER, Orhan DİKMEN, Farhad HABİBZADEH, Özgür AKTÜRK
Indexed In · Volume 162 / 2020
Estimation of the compaction characteristics of soils using the static compaction method
Authors:
Kamil KAYABALI, Ramin ASADİ, Mustafa FENER, Orhan DİKMEN, Farhad HABİBZADEH, Özgür AKTÜRK
ABSTRACT
Ground improvement using mechanical stabilization is commonly applied by performing the standard Proctor compaction test, which requires a significant quantity of soil, usually obtained from open pits. A static compaction test is an alternative laboratory compaction test. Although researchers have shown that the results of miniature size static compaction tests are comparable with that of standard Proctor tests in terms of the maximum dry density and the optimum water content, no attempt has been made to compare the two fundamental properties of the compacted soil: undrained shear strength and hydraulic conductivity. The scope of this investigation was to estimate the level of static compaction energy required to (1) obtain a compaction curve similar to that of the standard Proctor test; (2) reconstruct compacted soils using the standard Proctor and static compaction tests at the optimum water content; and (3) compare the undrained shear strength and hydraulic conductivity of compacted soils. The compacted soils at the predetermined energy level were subjected to hydraulic conductivity tests using the rigid-wall falling-head permeability method. Undrained shear strength tests were performed by employing a high-capacity laboratory vane shear apparatus on compacted samples of both the standard Proctor and static compaction tests. The present investigation revealed that the static compaction test, requiring about only 10% of the soil necessary to perform the standard Proctor method, provides comparable results in regard to hydraulic conductivity and undrained shear strength.
https://doi.org/10.19111/bulletinofmre.603873
Keywords:
Static compaction, Standard Proctor, Unconfined compressive strength, Permeability, Compaction energy.
Usability of PC-ash as lightweight aggregate in foam concrete
Authors:
Metin DAVRAZ, Şemsettin KILINÇARSLAN
ABSTRACT
Foam concretes can be produced with aggregate or without aggregate. In this study, the possibility of using PC ash as lightweight aggregate in the production of foam concrete was investigated. Waste- PC ash is emerging from the pulverized coal furnace about 10 tons/day in a textile factory located in the vicinity of Dinar (Afyonkarahisar). The chemical properties, particle size distribution and grain densities of PC-ash were determined. Foam concrete with a dry density of 450 kg/m3 at a cement dosage of 250 kg/m3 and w/c:0.65 was produced after the aggregate analysis. The PC-ash which is used in foam concrete mix is between 0 and 200 kg/m3. 100 mm cube and 300x300x50 mm prism samples were prepared with this foam concrete. The compressive strengths of the cube samples and the thermal conductivity coefficient of the prism samples were tested at the 28th day. The average compressive strength of foam concrete samples with a density of 452 kg/m3 was determined as 1.07 MPa and the thermal conductivity coefficient was determined as 0.097 W/mK. As a result, it has been determined that PC-ash as lightweight aggregate can be successfully used in production of precast element and light floor-screed.
https://doi.org/10.19111/bulletinofmre.545562
Keywords:
Foam concrete, Lightweight aggregate, PC ash, Compressive strength, Thermal conductivity.
Coal quality, mineralogy, petrography, and geochemistry of the high-strontium Bozburun lignite (Malatya, eastern Türkiye)
Authors:
Rıza Görkem OSKAY, Ali İhsan KARAYİĞİT
ABSTRACT
The Bozburun coalfield hosts a late Miocene 1.1 m thick coal seam. This study aims to determine coal quality, mineralogy, petrography and geochemistry, and controlling factors of elemental enrichments. The coals are generally black and greyish black in colour, and the low part of the seam commonly includes fossil shell remains. The ash yield displays a decreasing trend towards the upper part of the seam; in turn, gross calorific and total C values increase upwards. The total S content being generally higher than 5% (on dry basis), displays an increasing trend towards the upper part. In the entire seam, huminite is the most common maceral group, while inertinite and liptinite display variable proportions. The identified minerals by XRD are mainly quartz, clay minerals, calcite, pyrite, and aragonite (in fossil shell remains-bearing samples), whereas feldspars and marcasite determined in a few samples. Furthermore, in the coal samples, celestine and barite were identified
by SEM-EDX. This study indicates that precipitation of celestine and Sr-bearing barite grains during diagenetic stage and Sr-uptake by mollusc within the palaeomire caused Sr enrichment in the entire seam. Overall, the water influx and redox conditions controlled the mineralogical and the elemental compositions of the coal seam.
Ema ABRAHAM, Ayatu USMAN, Kelvin CHIMA, George-best AZUOKO, Iheanyi IKEAZOTA
Indexed In · Volume 173 / April 2024
Magnetic inversion modeling of subsurface geologic structures for mineral deposits mapping in southeastern Nigeria
Authors:
Ema ABRAHAM, Ayatu USMAN, Kelvin CHIMA, George-best AZUOKO, Iheanyi IKEAZOTA
ABSTRACT
Magnetic inversion techniques have been implemented to infer the extension and geometry of magnetic structures and also evaluate its influence on mineralization within Abakaliki and its environs, southeastern Nigeria. The modeling approach considers the techniques of threedimensional (3D) magnetic data inversion, Euler deconvolution, analytic signal inversion, Enhanced Local Wavenumber (ELW) Technique and Particle Swarm Optimization (PSO) to estimate source parameters and compare results. Model solutions were interpreted to represent possible geologic units with varying trends, housing mineralization within the study region. Results from inversion computation over some active mine locations show subsurface bodies with magnetic susceptibilities >0.00188 SI. Model results also show structural sources with almost 5.5 km depth extension, stretching 18 km in the EW direction at Ngbo – Ekerigwe location. This could imply significant mineral deposits at the location. Inversion of both magnetic anomaly and analytical signal enabled derivation of the actual subsurface structures in the region, with most of the structures appearing as dykes with depths ranging from 0.2 – 1.8 km at most of the mining sites. Location and depths of some of the modeled intrusions have been corroborated with the active on-site mines. The delineation of mineralization structures by this study would guide systematic exploration in the region.
Keywords:
Magnetic modeling; Aeromagnetic data; Particle Swarm Optimization (PSO); Minerals; Depths.
Şükrü Onur KARACA, Gültekin ERTEN, Semih ERGİNTAV, Shuhab D. KHAN
Indexed In · Volume 173 / April 2024
Anthropogenic problems threatening major cities: Largest surface deformations observed in Hatay, Türkiye based on SBAS-InSAR
Authors:
Şükrü Onur KARACA, Gültekin ERTEN, Semih ERGİNTAV, Shuhab D. KHAN
ABSTRACT
The surface deformation caused by tectonic activities and anthropogenic factors poses a great threat to cities worldwide. The investigation and monitoring of these deformations are crucial in order to create risk analysis for the future. The problem in this case is to investigate the surface deformations and their negative effects caused by groundwater use and to identify possible landslide areas. In this study, the surface deformations in Hatay province were analyzed using SBAS-InSAR. The results from these analyses were evaluated by field observations. Sentinel-1 descending (183 datasets) and ascending (147 datasets) track geometries were selected to determine the surface deformation and its temporal evolution. Both east-west and vertical surface deformations were calculated, and the surface deformation profiles, surface 3D models and time series were created. These time series were associated with monthly precipitation data. The deformation area was interpreted with regard to available well-log data and geological setting of the study area. As a result of the study, a surface deformation resembling a bowl like structure was observed in the industrial zone located in the city center of Hatay-Güzelburç. The deformation rates are approximately 22.3 cm/year in the form of subsidence, 3.6 cm/year in the form of eastern movement and 10.1 cm/year in the form of western movement. The deformation of this bowllike structure decelerated in the winter and accelerated in the summer due to excessive water use. The average monthly precipitation dataset supports these results. The stratigraphic data from water wells and the presence of limestone outside the eastern boundary of the deformation area show a thick clay layer in the eastern block of the bowl-shaped deformation structure. The difference between these two units, which causes a sharp anomaly at the eastern border of the deformation area, is interpreted as a probable normal fault. The second study area where surface deformations are observed is the landslide zone. The deformation was found to be 7.5 cm/year in a westward direction and 1.5 cm/year as subsidence.