Home›Modelling and computation of gravitational attraction, gradient tensors, rotational and horizontal invariants of Asteroid Bennu (101955), Itokawa (25143) and Eros (433) via 2D Non-Uniform FFT
Article Details
Modelling and computation of gravitational attraction, gradient tensors, rotational and horizontal invariants of Asteroid Bennu (101955), Itokawa (25143) and Eros (433) via 2D Non-Uniform FFT
BULLETIN OF THE MINERAL RESEARCH AND EXPLORATION (MTA Dergisi)
Article Details
Modelling and computation of gravitational attraction, gradient tensors, rotational and horizontal invariants of Asteroid Bennu (101955), Itokawa (25143) and Eros (433) via 2D Non-Uniform FFT
The internal structure and mass distribution of the terrestrial objects are yet unknown. The 2D gravity model with a constant density of the terrestrial objects can shed light on the surficial or textural heterogeneity due to topographic variations of the terrestrial objects. Three different steroids, which are Bennu (101955), Itokawa (25143) and Eros (433) are modelled in this study. During the modelling phase, a different number of edges, elements, nodes, and faces are used to describe the 3D models of Bennu, Itokawa, and Eros. These 3D models are used in 2D Non-Uniform Fast Fourier Transform (NU-FFT) applications to obtain gravitational attraction with a constant density polyhedron model. Tensor gradients and tensor invariants of the modelled gravity anomaly are calculated. Three major outcomes are interpreted from tensor gradient and tensor invariants. Firstly, textural heterogeneity due to relatively low topography is detected in the central part of Bennu. Secondly, considerably different properties which can be related to surface variations between the two lobes of Itokawa are observed. Lastly, directional surficial heterogeneities were detected in Eros.
Kosovo is located in a key position in the central-west part of the Balkans providing an opportunity to understand the far-field effects of distributed intracontinental deformation caused by the Aegean extension in the south and Adriatic compression in the west. It is also situated along the NE-SW trending Shkodër-Pejë transverse zone, where the Dinarides and Albanides-Hellenides orogenic belts are juxtaposed. While the instrumental seismicity of Kosovo indicates the activity of this fault zone and many others, the active faults in the country were not discussed in detail in the current literature. In this study, we analyzed both the geomorphic and structural features of major mountain front faults in western Kosovo (i.e., Pejë, Istog, Krojmir, and Prizren faults) to reveal the relative assessment of their activities and kinematic characters. Geomorphic and morphometric analyses of all the studied four different mountain fronts indicated high activity and tectonic uplift rates of over 0.5 mm/a. On the other hand, according to the collected kinematic data from the observed fault planes, the studied faults are mainly of normal character representing a dominance of NWSE- directed extension in western Kosovo, which is most probably caused by the rollback of the subducting slab in the Hellenic trench.
Keywords:
Neotectonics, Extensional Tectonics, Shkodër-Pejë Fault Zone, Balkans, Southeast Europe.
Hafiz MOHAMMED NAZİFİ, Ertan PEKŞEN, Ertuğrul GÜRBÜZ, Levent GÜLEN
Indexed In · Volume 173 / April 2024
Time-lapse ground penetrating radar (GPR) imaging of used engine oil contamination
Authors:
Hafiz MOHAMMED NAZİFİ, Ertan PEKŞEN, Ertuğrul GÜRBÜZ, Levent GÜLEN
ABSTRACT
Time-Lapse Ground Penetrating Radar (GPR) was employed to study used engine oil (UEO) contamination of sandy environment in laboratory setting. GPR is a near-surface geophysical method that uses electromagnetic field to provide image of the dielectric properties of earth materials to detect structures and changes in material properties within the subsurface. This research aimed to detect, monitor and map the migration of UEO contaminant in sand. The results of this study revealed that the migration of the UEO contamination in homogeneously laid sand is non-uniform. UEO plumes were identified as high amplitude signals with enhanced reflectivity. There was a progressive decrease in GPR signal amplitudes (reflection reduction) within the contaminated area of the tank with time. This decrease of GPR signal amplitudes was interpreted as caused by the evaporation of some portion of the UEO in the vadose zone as a result of temperature increase in time and also due to the occurrence of UEO biodegradation. The time-lapse GPR proved to be an effective technique for detecting, monitoring, and mapping UEO migration within sand tank in laboratory setting.
Kamil KAYABALI, Turgay BEYAZ, İlknur KARAASLAN ÖZDEMİR, Deniz YILMAZ
Indexed In · Volume 173 / April 2024
A simple and practical tool for indirect determination of the unconfined compressive strength of most common construction materials
Authors:
Kamil KAYABALI, Turgay BEYAZ, İlknur KARAASLAN ÖZDEMİR, Deniz YILMAZ
ABSTRACT
Determination of the unconfined compressive strength (UCS) of construction materials in the laboratory is tedious and time-consuming. There have been many attempts to indirectly predict UCS using simpler tools and techniques. One of them is the nail gun. The scope of this investigation is to design a nailer which can be applied all construction materials whose UCS range from 1-100 MPa. In the research, rocks, bricks, and concretes prepared in different cement/sand ratios with different strength ranges were used as materials. The unconfined compressive strength of the materials used in the experiments was first determined by conventional compression tests. The nail penetration depths were determined by conducting experiments on the same materials using a nailer with two different energy levels. An empirical relationship was developed by using nail penetration depths, driving energies, and nail diameters as the independent variables and the UCS determined by the conventional method as the dependent variable. According to the empirical relationship determined by multiple regression analysis, the UCS of building materials can be estimated with significance level of 99% by the nail penetration method. The research also revealed that the UCS of rocks might have a coefficient of variation as high as 30%.
Keywords:
Compressive strength, building materials, nail gun, driving energy.