In this study, studies were carried out to take rubidium (Rb), which is in a complex form of Na +K feldspar, pyroxene, and alumina silicate into solution in an environmentally sensitive manner with high recovery. Malatya - Kuluncak complex ore was used in this study. In the first stage of the study, the roasting method was tried to obtain rubidium chloride (RbCl) or rubidium sulphate (Rb2SO4) structures, which are the water-soluble forms of rubidium in the sodium-potassium feldspar structure. Roasting was carried out using different additives and calcium chloride was identified as the most suitable additive material for this ore structure. In studies investigating the effect of roasting temperature and time, the evaporation amount of RbCl was calculated. After deciding on the additives, the additive amount, solid/liquid ratio in the leaching stage, and leach time were optimized. The optimum conditions were determined as a leaching time of 120 minutes at 1/3 solid/ liquid ratio after roasting for 60 minutes at the roasting temperature of 900 °C at 70% calcium chloride (CaCl2) addition. the solution efficiency of rubidium was calculated as 96%. Taking Rb into solution from primary sources was first achieved with this study in Türkiye.
Mehmet ÇÖTELİ, Mustafa ALBAYRAK, Ufuk KİBAR, Arzu YAVUZ, Gülsüm TURGUT, Duran Serdar KARAHAN
Indexed In · Volume 176 / April 2025
Mineralogical examination of biomass ashes: A preliminary study for potassium enrichment and phosphoric acid (H3PO4) production
Authors:
Mehmet ÇÖTELİ, Mustafa ALBAYRAK, Ufuk KİBAR, Arzu YAVUZ, Gülsüm TURGUT, Duran Serdar KARAHAN
ABSTRACT
In this study, biomass fly ash was investigated and determined by XRD (XRay Diffractometer) to be predominantly langbeinite, aphthitalite, sylvine, apatite and hydroxyapatite. An alkaline leaching study was carried out on the material in a glass reactor at l/s ratio 4 temperature 60°C at pH 12.85 and after drying was analyzed by ICP (Inducted couple plasma). The crystal structure composition of K2SO4 72.28% and potassium content of 33.47% (w/w) was recovered. The elemental transformations in this leaching process were: K 74.16%, Mg 0.55% was found to be 0.8%. It was found that a minimum of 4.84 g H2SO4 per 100 g fly ash was required to precipitate the Ca(OH)2 migrated into the liquid solution and the overall leaching efficiency was found to be 29.85%. In the alkaline leaching process, potassium was found to be easily recovered from each biomass ash. By adding 40 g H2SO4/100 g biomass waste remaining after leaching, a phosphorus recovery of 74.9% was observed. In this preliminary study, unsatisfactory results were obtained in obtaining the industry standard H3PO4. The reason for this is that the Al, Mg and K in the fly ash are subject to selective dissolution as a result of working at high pH in the alkaline leaching process.
Haydar GÜNEŞ, Hüseyin Eren OBUZ, Hasan AKÇAY, Çiğdem KARA, Ayşe ERDEM
Indexed In · Volume 170 / April 2023
Production of rare-earth oxides from Eskişehir-Beylikova complex ores
Authors:
Haydar GÜNEŞ, Hüseyin Eren OBUZ, Hasan AKÇAY, Çiğdem KARA, Ayşe ERDEM
ABSTRACT
In this study, the production technology of barite, fluorite, rare-earth elements, and thorium-bearing rare-earth oxides from the Eskişehir-Beylikova were investigated, and the processes that can be used in the production of thorium-free mixed rare earth oxides were tested. The applied processes are roasting, leaching, solvent extraction and precipitation methods, respectively. After all studies, the optimum roasting temperature and roasting duration are determined as 600 °C and 1 hour. In the extraction stage, the highest leaching efficiency is achieved with 5 M HCl, 1-hour leaching duration, 1/3 solid/liquid ratio and 35 °C leaching temperature. While methyl tri C8-C10 ammonium chloride (Adogen 464) is used for the removal of iron from produced solution, di-(2-ethylhexyl) phosphoric acid (D2EHPA) is used for the removal of thorium. As a result of solvent extraction studies, the solution containing rare earth elements is precipitated under optimum conditions. After precipitation, the product contains 99.65% rare earth oxides.
Bekir BAŞKURT, Mete Tayhan SERDENGEÇTİ, Kaan ÖZÇELİK, Hüseyin BAŞTÜRKCÜ
Indexed In · Volume 169 / 2022
Recovery of Cu-Ce from copper slag by using flotation and chemical methods
Authors:
Bekir BAŞKURT, Mete Tayhan SERDENGEÇTİ, Kaan ÖZÇELİK, Hüseyin BAŞTÜRKCÜ
ABSTRACT
In our days, slags are considered secondary resources due to the metals they contain. Copper slags having economical operating grades in terms of Zn, Cu, Ce, Ni, Co, Mo, and V, have complex mineralogy due to their thermal processing based formations. Methods of recovery for copper and other precious metals from slags, have been studied, and for which, flotation plants in industrial scale are operated. In cases where physical or physico-chemical mineral processing methods are not sufficient, hydrometallurgical methods are applied. In this study, the flotation method was applied to a copper slag with 0.9% Cu grade. Copper recovery and the concentration grade were determined to be approximately 40 and 22.7% Cu, respectively. Metal extractions were examined through direct leaching tests. Using H2SO4 in the leaching, resulted in gel formation, leading to an investigation of the leach parameters using HCl. Cu and Ce extractions of around 70-80% were attained as a result of a test performed for 2 hours with the addition of 25 g/L H2O2 at a rate of 20-25% solids and 300 g/L HCl concentration. An examination of the metal relations, indicated that the dissolution behavior of Cu and Ce was quite similar to the Al dissolution (R2=0.9).
https://doi.org/10.19111/bulletinofmre.1139294
A graph method for interpretation of magnetic anomalies over 2D dikes and vertical faults
Authors:
İbrahim KARA, Oya TARHAN BAL, Anisya B.TEKKELİ
ABSTRACT
Simple geometric assumptions for dikes and faults are often used for interpreting the parameters of these structures from magnetic anomalies. The magnetic anomaly of a 2D dike or a vertical fault consists of two components; one with even and the other with odd symmetries. The function resulting from the ratio of the even and odd components is independent from the amplitude coefficient. The abscissa of the half-maximum of the even component and the maximum of the odd component of a dike or a vertical fault is related to its depth and its half-width. Incorporating this relation into the corresponding equations for dikes and vertical faults, the half-width value can be eliminated from the equations. Thus, the resulting ratio can be used for determining the model parameters. Using the ratio of the even component to the odd component for given distances, curves can be obtained for different depth-index parameter pairs, and from the graph of these curves, parameters of 2D dikes and vertical faults can be determined. The validity of the method is tested using synthetic models for dike and vertical fault cases. The method is also implemented on two different field data, and the results obtained are compared to previous studies.
Keywords:
Magnetic Interpretation, 2D Dike, Vertical Fault, Graph Method.
Separation efficiency of different methods in treatment of a low-grade iron ore
Authors:
Özgür ÖZCAN
ABSTRACT
In the present study, characterization and beneficiation tests were performed on an iron ore sample for the evaluation of separation efficiency (SE) of different methods. Results showed that the decrease in feed size fraction increases the SE irrespective of to beneficiation method. It was determined from the liberation analyses that the increase in SE values at finer size fractions is related with higher liberation. Calculated SE values revealed that operational parameters significantly affect the SE of all methods and the net forces acting on particles play an important role on SE of different size fractions. Mean SE of different size fractions showed that the separation efficiencies of gravity concentration and magnetic separation takes similar values above 1 mm, however, SE of magnetic separation is significantly higher than gravity concentration below 1 mm for the studied sample. For low grade ores, it is very crucial to develop a flow sheet to achieve the optimum grade and recovery while decreasing the cost likely by using optimum method. Therefore, SE calculations used in this research can be used as a basic method to compare the efficiency of different beneficiation methods. SE method has advantages as they provide fast evaluation of efficiency by using experimental results.
Keywords:
Separation Efficiency Grade, Recovery, Magnetic Separation, Gravity Concentration.
Coulomb stress changes and magnitude-frequency distribution for Lake Van region
Authors:
Hamdi ALKAN, Erdem BAYRAK
ABSTRACT
The tectonic structure of Türkiye is under the influence of Arabian, Eurasian, African, and Anatolian plates. Lake Van region, located in eastern Türkiye, has been exposed to many devastating earthquakes in historical and instrumental periods. In this paper, using regional earthquakes, the tectonic stress variation of Lake Van region was investigated using the Coulomb stress change and the b-value distribution. 83 earthquakes that occurred between 2000 and 2020 are used to calculate the Coulomb stress change, while 17815 earthquakes that occurred between 1903 and 2021 are used to calculate the b-value distribution. Coulomb stress change gives an idea about the transfer of energy to nearby faults. Coulomb stress change and b-value distribution maps were created at different depths to model the variation of stress. The low b-values and positive Coulomb stress values were especially observed around the Van and Yeniköşk faults. On the contrary, no significant variation in stress change was observed around Süphan and Nemrut volcanoes, and high b-values were calculated in this region. Coulomb stress change and earthquake epicentral distribution are compatible and most events occurred in positive stress regions. In conclusion, stress change and b-value distribution were interpreted together and positive stress regions were revealed in the region.
Keywords:
Eastern Turkey, Van Lake Region, Coulomb Stress, b-value, Seismotectonic.