Volume 168 · 2022 · 11 ARTICLES
All Articles In This Issue
01
Indexed In · Volume 168 / 2022
A graph method for interpretation of magnetic anomalies over 2D dikes and vertical faults
Authors: ABSTRACTSimple geometric assumptions for dikes and faults are often used for interpreting the parameters of these structures from magnetic anomalies. The magnetic anomaly of a 2D dike or a vertical fault consists of two components; one with even and the other with odd symmetries. The function resulting from the ratio of the even and odd components is independent from the amplitude coefficient. The abscissa of the half-maximum of the even component and the maximum of the odd component of a dike or a vertical fault is related to its depth and its half-width. Incorporating this relation into the corresponding equations for dikes and vertical faults, the half-width value can be eliminated from the equations. Thus, the resulting ratio can be used for determining the model parameters. Using the ratio of the even component to the odd component for given distances, curves can be obtained for different depth-index parameter pairs, and from the graph of these curves, parameters of 2D dikes and vertical faults can be determined. The validity of the method is tested using synthetic models for dike and vertical fault cases. The method is also implemented on two different field data, and the results obtained are compared to previous studies.
Keywords:
02
Indexed In · Volume 168 / 2022
Efficiency of singularity and PCA mapping of mineralization-related geochemical anomalies: a comparative study using BLEG and <180μm stream sediment geochemical data
Authors: ABSTRACTIn gold (Au) exploration, the analysis of both bulk leach extractable gold (BLEG) and acid-extractable Au in the
Keywords:
03
Indexed In · Volume 168 / 2022
A comparison of ion-exchange resins and activated carbon in recovering gold from cyanide leach solutions with low levels of copper
Authors: ABSTRACTThis study was conducted to determine the effectiveness of three different adsorbents for the adsorption of gold from a real cyanide leach liquor. An activated carbon (NORIT GAC 1240), strong base (Purogold A194), and weak base (Purogold S992) resins were tested as the adsorbents. The pregnant leach solution (PLS) was derived from cyanide leaching (1.5 g/L NaCN, 25% w/w solids ratio, 1.5 L/min air flow rate, pH 10.5 – 11, 24 h) of the roasted copper-rich refractory gold ore pretreated with H2SO4. Gold and copper concentrations in the PLS were analysed to be 26.1 mg/L Au and 62.4 mg/L Cu, respectively. Activated carbon was found to be the best performing adsorbent as it achieved the highest gold loading. Purogold A194 loaded the highest amount of copper amongst the adsorbents tested. Despite the fact that activated carbon loaded a high amount of gold, it was less selective than Purogold S992. Purogold A194 exhibited the lowest selectivity, which was defined as the distribution ratio of gold to copper, compared with Purogold S992 and activated carbon. Therefore, the order of selectivity of the adsorbents tested was as follows: Purogold S992 > Activated carbon > Purogold A194.
Keywords:
04
Indexed In · Volume 168 / 2022
Sedimentology and Miocene-Pliocene depositional evolution of the stream-dominated alluvial fan deposits at circum-Sultandağları region
Authors: ABSTRACTYalvaç and Ilgın basins surrounding Sultandağları were opened due to the orogenic collapse in the early Miocene. The NW-SE trending Çakırçal and Akşehir fault zones, forming boundaries with these basins, caused both the opening of the basins and uplifting of Sultandağları. During the Miocene-Pliocene period, the alluvial fans fed from Sultandağları developed on the basin margins, while the lacustrine carbonate and clastic depositions formed in the basin’s interior. The alluvial fan deposits are laterally and vertically transitional with lacustrine sediments and alternate several times in the sequence. The alluvial fans, widespread in the region, consist of debris flow, hyperconsantrated stream flood, braided river and meandering river deposits. Fan deposits that pass from high-energy fluvial facies at the basin margin to the low-energy fluvial facies towards the basin interior have been interpreted as stream-dominated alluvial fan deposits. The age data obtained from the fan deposits of the Yalvaç and the Ilgın basins show that Sultandağları concurrently feeds the alluvial fans on both flanks. Alluvial fan deposition around Sultandağları formed under the control of tectonic and climatic processes. The tectonism led to the formation of basins and source areas. Simultaneously, the climate maintained the streams to be perennial by precipitation, thus proving a continuous sediment supply to the basins. Tectonism and climate-controlled base-level changes determined the quantity of sediments carried to the basin from the source area, causing regressive or transgressive developments.
Keywords:
05
Indexed In · Volume 168 / 2022
Mud systems applied to problematic formations in core drilling rigs
Authors: ABSTRACTThe two most important features of drilling rigs based on the core drilling principles are the drill set rotating at high speeds and the very precise spacing between the pipe and the well wall. Formation pieces that swell, flow into the well, spill or collapse during the drilling of problematic formations mix into the mud or narrow the annulus and cause well problems by restraining the rotation of the drill string and circulation. The spilled formation pieces cause an excessive solid material increase in the mud structure and due to the effect of centrifugal force, the solids adhere to the inner wall of the pipes near the surface and form a cake. Excessive cake thickness in the pipes obstruct the descent of the core barrel inner tube catcher into the well. During the removal of the inner tube, a vacuum occurs in the well due to the mud discharged from the rod and the problematic formations are poured into the annulus and block the core between the core barrel and the well wall. In this study, the performance of mud systems determined by trial and error method against the problems encountered in unconsolidated claystone, mudstone (shale), siltstone and sand - pebble stones in core coal exploration drillings in Çorum - Amasya region were evaluated. Monitoring and regular improvement of the rheological values of the mud compositions, changing the mud composition according to the well conditions, keeping the gel strength high and increasing its density with salt was found to play an important role in keeping the unconsolidated formations physically balanced. Salt mud also minimized the formation of cake in the pipe.
Keywords:
06
Indexed In · Volume 168 / 2022
Separation efficiency of different methods in treatment of a low-grade iron ore
Authors: ABSTRACTIn the present study, characterization and beneficiation tests were performed on an iron ore sample for the evaluation of separation efficiency (SE) of different methods. Results showed that the decrease in feed size fraction increases the SE irrespective of to beneficiation method. It was determined from the liberation analyses that the increase in SE values at finer size fractions is related with higher liberation. Calculated SE values revealed that operational parameters significantly affect the SE of all methods and the net forces acting on particles play an important role on SE of different size fractions. Mean SE of different size fractions showed that the separation efficiencies of gravity concentration and magnetic separation takes similar values above 1 mm, however, SE of magnetic separation is significantly higher than gravity concentration below 1 mm for the studied sample. For low grade ores, it is very crucial to develop a flow sheet to achieve the optimum grade and recovery while decreasing the cost likely by using optimum method. Therefore, SE calculations used in this research can be used as a basic method to compare the efficiency of different beneficiation methods. SE method has advantages as they provide fast evaluation of efficiency by using experimental results.
Keywords:
07
Indexed In · Volume 168 / 2022
Modeling of the complex hydrocarbon traps by the shot domain acoustic finite difference method and data-processing
Authors: ABSTRACTNumerical modeling studies have a widespread application in exploration seismology in order to understand the seismic reflection responses of hydrocarbon traps formed in relation to tectonic structure, lithological changes and unconformities in complex geological environments and to develop effective data processing strategies. In this study, the seismic modeling of two important hydrocarbon trap models (Granite Wash and Normal Fault Trap) was performed by the Finite Difference Method (FDM), which provides the solution of the acoustic wave equation. Seismic data models were carried out in the pre-stack shot environment, and the obtained shot data were passed through appropriate data-processing stages to obtain stack and migration (zero offset) sections. By converting the obtained migration sections to depth, the spatial location and dimensions of hydrocarbon traps on the section were determined and it has been observed that they are compatible by comparing with the initial geological models. Thus, the seismic responses of hydrocarbon trap structures were learned, the importance of data processing was understood, and zero offset crosssections were obtained by processing of the generated synthetic shot records. Accordingly, it was observed that it is appropriate to make more and frequent shots in the investigation of granite wash type traps which are thin and short-width, whereas it is useful to make relatively less frequent shots in order to reduce the scattering intensity caused by the discontinuities of the fault type structures. Consequently, it is thought that before the field study for the hydrocarbon exploration, the modeling of the pre-stack shot instead of the post-stack modeling (zero offset) will contribute to the development of the data processing stages and the testing of the seismic section interpretation. In the future, such synthetic models and data processing will be developed for different complex trap structures and real data.
Keywords:
08
Indexed In · Volume 168 / 2022
Interpretation of satellite gravity anomalies with pseudo-depth slicing method filter in Türkiye
Authors: ABSTRACTIn this study, discontinuities and major tectonic boundaries are interpreted in and around Türkiye by Bouguer gravity anomaly. The World Gravity Map 2012 is used for the interpretation of major tectonic features in the Anatolia Region. Radial average power spectrum (RAPS) and band-pass filter are used for long and short wavelength separation. For the whole study area, four depth segments are detected. Moreover, the radial average depths of these depth segments are 54.9 km, 32.2 km, 21.9 km and 8.0 km. In order to conduct better interpretation, the study area was divided into three subareas from the west to the east (area 1 to area 3). In area 1 (41.4 km, 21.2 km and 7.8 km) and area 2 (48.1 km, 20.0 km and 6.6 km), three depth sources are detected. Furthermore, four various depth segments are analysed in area 3 (54.3 km, 29.8 km, 20.8 km and 8.6 km). The interpretation of the whole study area, area 1, area 2 and area 3 showed that depth of the sediment accumulation in the Western Anatolia is estimated as 7.8 km.
Keywords:
09
Indexed In · Volume 168 / 2022
Extraction of rubidium from Malatya - Kuluncak area complex ore
Authors: ABSTRACTIn this study, studies were carried out to take rubidium (Rb), which is in a complex form of Na +K feldspar, pyroxene, and alumina silicate into solution in an environmentally sensitive manner with high recovery. Malatya - Kuluncak complex ore was used in this study. In the first stage of the study, the roasting method was tried to obtain rubidium chloride (RbCl) or rubidium sulphate (Rb2SO4) structures, which are the water-soluble forms of rubidium in the sodium-potassium feldspar structure. Roasting was carried out using different additives and calcium chloride was identified as the most suitable additive material for this ore structure. In studies investigating the effect of roasting temperature and time, the evaporation amount of RbCl was calculated. After deciding on the additives, the additive amount, solid/liquid ratio in the leaching stage, and leach time were optimized. The optimum conditions were determined as a leaching time of 120 minutes at 1/3 solid/ liquid ratio after roasting for 60 minutes at the roasting temperature of 900 °C at 70% calcium chloride (CaCl2) addition. the solution efficiency of rubidium was calculated as 96%. Taking Rb into solution from primary sources was first achieved with this study in Türkiye.
Keywords:
10
Indexed In · Volume 168 / 2022
Coulomb stress changes and magnitude-frequency distribution for Lake Van region
Authors: ABSTRACTThe tectonic structure of Türkiye is under the influence of Arabian, Eurasian, African, and Anatolian plates. Lake Van region, located in eastern Türkiye, has been exposed to many devastating earthquakes in historical and instrumental periods. In this paper, using regional earthquakes, the tectonic stress variation of Lake Van region was investigated using the Coulomb stress change and the b-value distribution. 83 earthquakes that occurred between 2000 and 2020 are used to calculate the Coulomb stress change, while 17815 earthquakes that occurred between 1903 and 2021 are used to calculate the b-value distribution. Coulomb stress change gives an idea about the transfer of energy to nearby faults. Coulomb stress change and b-value distribution maps were created at different depths to model the variation of stress. The low b-values and positive Coulomb stress values were especially observed around the Van and Yeniköşk faults. On the contrary, no significant variation in stress change was observed around Süphan and Nemrut volcanoes, and high b-values were calculated in this region. Coulomb stress change and earthquake epicentral distribution are compatible and most events occurred in positive stress regions. In conclusion, stress change and b-value distribution were interpreted together and positive stress regions were revealed in the region.
Keywords:
11
Indexed In · Volume 168 / 2022
Accurate whole-rock geochemistry analysis by combined ICP-OES and LA-ICP-MS instruments
Authors: ABSTRACTICP-OES and LA-ICP-MS instruments routinely used to assess the geochemical properties of the various natural and synthetic materials. In this contribution, the analytical routines and method development procedures of the ICP-OES and LA-ICP-MS facilities installed at the İstanbul University-Cerrahpaşa Geological Engineering Department, Geochronology and Geochemistry Laboratory have been evaluated using well-known international rock standards. Sample preparation techniques, method development, experimental setup and measurement conditions for the both ICP-OES and LA-ICP-MS instruments were discussed and specific analyze results of NIST SRM 614, BCR-2, AGV-2, BCR-2G and AGV-2G were evaluated. Flux-free USGS glass standards were produced by in-house techniques and flux-bearing glasses were produced by fusion of sample with the mixture of ultra-pure lithium-tetraborate, lithium metaborate and lithiumbromide were evaluated and compared with the well-known reference values in the literature. Relative standard deviation (RSD) values for the major oxide measurements for standards changes between of 0.0 wt. % to 1.5 wt. %. RSD values for the trace and rare-earth-elements values were mainly lower than 10 wt. %. The results confirm that the both flux-bearing and flux-free glasses reasonably match with the world-wide inter-laboratory values for international standards samples. The combination of these two instruments can be used to conduct geochemistry of various solid earth materials.
Keywords:
No articles match your search.