Yalvaç Basin, Ilgın Basin, Braided River, Meandering River, Forced Regression.
Abstract:
Yalvaç and Ilgın basins surrounding Sultandağları were opened due to the orogenic collapse in the early Miocene. The NW-SE trending Çakırçal and Akşehir fault zones, forming boundaries with these basins, caused both the opening of the basins and uplifting of Sultandağları. During the Miocene-Pliocene period, the alluvial fans fed from Sultandağları developed on the basin margins, while the lacustrine carbonate and clastic depositions formed in the basin’s interior. The alluvial fan deposits are laterally and vertically transitional with lacustrine sediments and alternate several times in the sequence. The alluvial fans, widespread in the region, consist of debris flow, hyperconsantrated stream flood, braided river and meandering river deposits. Fan deposits that pass from high-energy fluvial facies at the basin margin to the low-energy fluvial facies towards the basin interior have been interpreted as stream-dominated alluvial fan deposits. The age data obtained from the fan deposits of the Yalvaç and the Ilgın basins show that Sultandağları concurrently feeds the alluvial fans on both flanks. Alluvial fan deposition around Sultandağları formed under the control of tectonic and climatic processes. The tectonism led to the formation of basins and source areas. Simultaneously, the climate maintained the streams to be perennial by precipitation, thus proving a continuous sediment supply to the basins. Tectonism and climate-controlled base-level changes determined the quantity of sediments carried to the basin from the source area, causing regressive or transgressive developments.
Deus Albert MSUMANGE, Ersin Yener YAZICI, Oktay CELEP, Hacı DEVECİ
Indexed In · Volume 168 / 2022
A comparison of ion-exchange resins and activated carbon in recovering gold from cyanide leach solutions with low levels of copper
Authors:
Deus Albert MSUMANGE, Ersin Yener YAZICI, Oktay CELEP, Hacı DEVECİ
ABSTRACT
This study was conducted to determine the effectiveness of three different adsorbents for the adsorption of gold from a real cyanide leach liquor. An activated carbon (NORIT GAC 1240), strong base (Purogold A194), and weak base (Purogold S992) resins were tested as the adsorbents. The pregnant leach solution (PLS) was derived from cyanide leaching (1.5 g/L NaCN, 25% w/w solids ratio, 1.5 L/min air flow rate, pH 10.5 – 11, 24 h) of the roasted copper-rich refractory gold ore pretreated with H2SO4. Gold and copper concentrations in the PLS were analysed to be 26.1 mg/L Au and 62.4 mg/L Cu, respectively. Activated carbon was found to be the best performing adsorbent as it achieved the highest gold loading. Purogold A194 loaded the highest amount of copper amongst the adsorbents tested. Despite the fact that activated carbon loaded a high amount of gold, it was less selective than Purogold S992. Purogold A194 exhibited the lowest selectivity, which was defined as the distribution ratio of gold to copper, compared with Purogold S992 and activated carbon. Therefore, the order of selectivity of the adsorbents tested was as follows: Purogold S992 > Activated carbon > Purogold A194.
Separation efficiency of different methods in treatment of a low-grade iron ore
Authors:
Özgür ÖZCAN
ABSTRACT
In the present study, characterization and beneficiation tests were performed on an iron ore sample for the evaluation of separation efficiency (SE) of different methods. Results showed that the decrease in feed size fraction increases the SE irrespective of to beneficiation method. It was determined from the liberation analyses that the increase in SE values at finer size fractions is related with higher liberation. Calculated SE values revealed that operational parameters significantly affect the SE of all methods and the net forces acting on particles play an important role on SE of different size fractions. Mean SE of different size fractions showed that the separation efficiencies of gravity concentration and magnetic separation takes similar values above 1 mm, however, SE of magnetic separation is significantly higher than gravity concentration below 1 mm for the studied sample. For low grade ores, it is very crucial to develop a flow sheet to achieve the optimum grade and recovery while decreasing the cost likely by using optimum method. Therefore, SE calculations used in this research can be used as a basic method to compare the efficiency of different beneficiation methods. SE method has advantages as they provide fast evaluation of efficiency by using experimental results.
Keywords:
Separation Efficiency Grade, Recovery, Magnetic Separation, Gravity Concentration.
ICP-OES and LA-ICP-MS instruments routinely used to assess the geochemical properties of the various natural and synthetic materials. In this contribution, the analytical routines and method development procedures of the ICP-OES and LA-ICP-MS facilities installed at the İstanbul University-Cerrahpaşa Geological Engineering Department, Geochronology and Geochemistry Laboratory have been evaluated using well-known international rock standards. Sample preparation techniques, method development, experimental setup and measurement conditions for the both ICP-OES and LA-ICP-MS instruments were discussed and specific analyze results of NIST SRM 614, BCR-2, AGV-2, BCR-2G and AGV-2G were evaluated. Flux-free USGS glass standards were produced by in-house techniques and flux-bearing glasses were produced by fusion of sample with the mixture of ultra-pure lithium-tetraborate, lithium metaborate and lithiumbromide were evaluated and compared with the well-known reference values in the literature. Relative standard deviation (RSD) values for the major oxide measurements for standards changes between of 0.0 wt. % to 1.5 wt. %. RSD values for the trace and rare-earth-elements values were mainly lower than 10 wt. %. The results confirm that the both flux-bearing and flux-free glasses reasonably match with the world-wide inter-laboratory values for international standards samples. The combination of these two instruments can be used to conduct geochemistry of various solid earth materials.