Satellite Gravity Data, Spectral Methods, Pseudo - Depth Slicing Method, Radial Average Power Spectrum, Qualitative Interpretation.
Abstract:
In this study, discontinuities and major tectonic boundaries are interpreted in and around Türkiye by Bouguer gravity anomaly. The World Gravity Map 2012 is used for the interpretation of major tectonic features in the Anatolia Region. Radial average power spectrum (RAPS) and band-pass filter are used for long and short wavelength separation. For the whole study area, four depth segments are detected. Moreover, the radial average depths of these depth segments are 54.9 km, 32.2 km, 21.9 km and 8.0 km. In order to conduct better interpretation, the study area was divided into three subareas from the west to the east (area 1 to area 3). In area 1 (41.4 km, 21.2 km and 7.8 km) and area 2 (48.1 km, 20.0 km and 6.6 km), three depth sources are detected. Furthermore, four various depth segments are analysed in area 3 (54.3 km, 29.8 km, 20.8 km and 8.6 km). The interpretation of the whole study area, area 1, area 2 and area 3 showed that depth of the sediment accumulation in the Western Anatolia is estimated as 7.8 km.
Deus Albert MSUMANGE, Ersin Yener YAZICI, Oktay CELEP, Hacı DEVECİ
Indexed In · Volume 168 / 2022
A comparison of ion-exchange resins and activated carbon in recovering gold from cyanide leach solutions with low levels of copper
Authors:
Deus Albert MSUMANGE, Ersin Yener YAZICI, Oktay CELEP, Hacı DEVECİ
ABSTRACT
This study was conducted to determine the effectiveness of three different adsorbents for the adsorption of gold from a real cyanide leach liquor. An activated carbon (NORIT GAC 1240), strong base (Purogold A194), and weak base (Purogold S992) resins were tested as the adsorbents. The pregnant leach solution (PLS) was derived from cyanide leaching (1.5 g/L NaCN, 25% w/w solids ratio, 1.5 L/min air flow rate, pH 10.5 – 11, 24 h) of the roasted copper-rich refractory gold ore pretreated with H2SO4. Gold and copper concentrations in the PLS were analysed to be 26.1 mg/L Au and 62.4 mg/L Cu, respectively. Activated carbon was found to be the best performing adsorbent as it achieved the highest gold loading. Purogold A194 loaded the highest amount of copper amongst the adsorbents tested. Despite the fact that activated carbon loaded a high amount of gold, it was less selective than Purogold S992. Purogold A194 exhibited the lowest selectivity, which was defined as the distribution ratio of gold to copper, compared with Purogold S992 and activated carbon. Therefore, the order of selectivity of the adsorbents tested was as follows: Purogold S992 > Activated carbon > Purogold A194.
Mud systems applied to problematic formations in core drilling rigs
Authors:
Bülent TOKA
ABSTRACT
The two most important features of drilling rigs based on the core drilling principles are the drill set rotating at high speeds and the very precise spacing between the pipe and the well wall. Formation pieces that swell, flow into the well, spill or collapse during the drilling of problematic formations mix into the mud or narrow the annulus and cause well problems by restraining the rotation of the drill string and circulation. The spilled formation pieces cause an excessive solid material increase in the mud structure and due to the effect of centrifugal force, the solids adhere to the inner wall of the pipes near the surface and form a cake. Excessive cake thickness in the pipes obstruct the descent of the core barrel inner tube catcher into the well. During the removal of the inner tube, a vacuum occurs in the well due to the mud discharged from the rod and the problematic formations are poured into the annulus and block the core between the core barrel and the well wall. In this study, the performance of mud systems determined by trial and error method against the problems encountered in unconsolidated claystone, mudstone (shale), siltstone and sand - pebble stones in core coal exploration drillings in Çorum - Amasya region were evaluated. Monitoring and regular improvement of the rheological values of the mud compositions, changing the mud composition according to the well conditions, keeping the gel strength high and increasing its density with salt was found to play an important role in keeping the unconsolidated formations physically balanced. Salt mud also minimized the formation of cake in the pipe.
Modeling of the complex hydrocarbon traps by the shot domain acoustic finite difference method and data-processing
Authors:
Şerife BOĞAZKESEN, Hakan KARSLI
ABSTRACT
Numerical modeling studies have a widespread application in exploration seismology in order to understand the seismic reflection responses of hydrocarbon traps formed in relation to tectonic structure, lithological changes and unconformities in complex geological environments and to develop effective data processing strategies. In this study, the seismic modeling of two important hydrocarbon trap models (Granite Wash and Normal Fault Trap) was performed by the Finite Difference Method (FDM), which provides the solution of the acoustic wave equation. Seismic data models were carried out in the pre-stack shot environment, and the obtained shot data were passed through appropriate data-processing stages to obtain stack and migration (zero offset) sections. By converting the obtained migration sections to depth, the spatial location and dimensions of hydrocarbon traps on the section were determined and it has been observed that they are compatible by comparing with the initial geological models. Thus, the seismic responses of hydrocarbon trap structures were learned, the importance of data processing was understood, and zero offset crosssections were obtained by processing of the generated synthetic shot records. Accordingly, it was observed that it is appropriate to make more and frequent shots in the investigation of granite wash type traps which are thin and short-width, whereas it is useful to make relatively less frequent shots in order to reduce the scattering intensity caused by the discontinuities of the fault type structures. Consequently, it is thought that before the field study for the hydrocarbon exploration, the modeling of the pre-stack shot instead of the post-stack modeling (zero offset) will contribute to the development of the data processing stages and the testing of the seismic section interpretation. In the future, such synthetic models and data processing will be developed for different complex trap structures and real data.