The two most important features of drilling rigs based on the core drilling principles are the drill set rotating at high speeds and the very precise spacing between the pipe and the well wall. Formation pieces that swell, flow into the well, spill or collapse during the drilling of problematic formations mix into the mud or narrow the annulus and cause well problems by restraining the rotation of the drill string and circulation. The spilled formation pieces cause an excessive solid material increase in the mud structure and due to the effect of centrifugal force, the solids adhere to the inner wall of the pipes near the surface and form a cake. Excessive cake thickness in the pipes obstruct the descent of the core barrel inner tube catcher into the well. During the removal of the inner tube, a vacuum occurs in the well due to the mud discharged from the rod and the problematic formations are poured into the annulus and block the core between the core barrel and the well wall. In this study, the performance of mud systems determined by trial and error method against the problems encountered in unconsolidated claystone, mudstone (shale), siltstone and sand - pebble stones in core coal exploration drillings in Çorum - Amasya region were evaluated. Monitoring and regular improvement of the rheological values of the mud compositions, changing the mud composition according to the well conditions, keeping the gel strength high and increasing its density with salt was found to play an important role in keeping the unconsolidated formations physically balanced. Salt mud also minimized the formation of cake in the pipe.
Choosing the composition of a drilling fluid containing partially hydrolyzed polyacrylamides (PHPA) for core drillings
Authors:
Bülent TOKA
ABSTRACT
In core (diamond) drilling operations, the controlling of drilling fluid’s rheological and filtration properties within specific value ranges is essential to ensure effective well cleaning and the maintenance of both mechanical and chemical equilibrium within the well. Furthermore, the additives in the fluid contribute significantly to improving core recovery efficiency. Partially hydrolyzed polyacrylamides (PHPA), known for their ability to encapsulate formations and drill cuttings to prevent the interaction of active clays with water, are also recognized for their effectiveness in improving core recovery efficiency. In core drilling operations, the high-speed rotation of the drill string can lead to challenges such as cake formation when the drilling fluid contains excessive solid particles (e.g., bentonite, calcite, barite, or drill cuttings). Drilling fluid engineers typically prefer polymer-based fluids with low solids content to reduce these issues. In this study, the rheological and filtration properties of various low-solids fluid compositions containing PHPA were investigated under laboratory conditions to identify the most suitable formulations for core drilling. The results of tests revealed that fluid compositions incorporating calcite + xanthan gum + modified starch + PHPA and bentonite + xanthan gum + modified starch + PHPA exhibited superior rheological and filtration properties compared to other fluid formulations. Additionally, the composition of PAC L + PHPA + calcium carbonate exhibited rheological and filtration values suitable for core drilling applications.
ICP-OES and LA-ICP-MS instruments routinely used to assess the geochemical properties of the various natural and synthetic materials. In this contribution, the analytical routines and method development procedures of the ICP-OES and LA-ICP-MS facilities installed at the İstanbul University-Cerrahpaşa Geological Engineering Department, Geochronology and Geochemistry Laboratory have been evaluated using well-known international rock standards. Sample preparation techniques, method development, experimental setup and measurement conditions for the both ICP-OES and LA-ICP-MS instruments were discussed and specific analyze results of NIST SRM 614, BCR-2, AGV-2, BCR-2G and AGV-2G were evaluated. Flux-free USGS glass standards were produced by in-house techniques and flux-bearing glasses were produced by fusion of sample with the mixture of ultra-pure lithium-tetraborate, lithium metaborate and lithiumbromide were evaluated and compared with the well-known reference values in the literature. Relative standard deviation (RSD) values for the major oxide measurements for standards changes between of 0.0 wt. % to 1.5 wt. %. RSD values for the trace and rare-earth-elements values were mainly lower than 10 wt. %. The results confirm that the both flux-bearing and flux-free glasses reasonably match with the world-wide inter-laboratory values for international standards samples. The combination of these two instruments can be used to conduct geochemistry of various solid earth materials.
Efficiency of singularity and PCA mapping of mineralization-related geochemical anomalies: a comparative study using BLEG and <180μm stream sediment geochemical data
Authors:
Fatma Nuran SÖNMEZ, Simay KOÇKAR, Hüseyin YILMAZ
ABSTRACT
In gold (Au) exploration, the analysis of both bulk leach extractable gold (BLEG) and acid-extractable Au in the
Coulomb stress changes and magnitude-frequency distribution for Lake Van region
Authors:
Hamdi ALKAN, Erdem BAYRAK
ABSTRACT
The tectonic structure of Türkiye is under the influence of Arabian, Eurasian, African, and Anatolian plates. Lake Van region, located in eastern Türkiye, has been exposed to many devastating earthquakes in historical and instrumental periods. In this paper, using regional earthquakes, the tectonic stress variation of Lake Van region was investigated using the Coulomb stress change and the b-value distribution. 83 earthquakes that occurred between 2000 and 2020 are used to calculate the Coulomb stress change, while 17815 earthquakes that occurred between 1903 and 2021 are used to calculate the b-value distribution. Coulomb stress change gives an idea about the transfer of energy to nearby faults. Coulomb stress change and b-value distribution maps were created at different depths to model the variation of stress. The low b-values and positive Coulomb stress values were especially observed around the Van and Yeniköşk faults. On the contrary, no significant variation in stress change was observed around Süphan and Nemrut volcanoes, and high b-values were calculated in this region. Coulomb stress change and earthquake epicentral distribution are compatible and most events occurred in positive stress regions. In conclusion, stress change and b-value distribution were interpreted together and positive stress regions were revealed in the region.
Keywords:
Eastern Turkey, Van Lake Region, Coulomb Stress, b-value, Seismotectonic.