Home›Assessment of crustal thinning and tectonic stress distribution of Gülbahçe fault zone and its surroundings (İzmir, West Türkiye) using gravity and magnetic anomalies
Article Details
Assessment of crustal thinning and tectonic stress distribution of Gülbahçe fault zone and its surroundings (İzmir, West Türkiye) using gravity and magnetic anomalies
BULLETIN OF THE MINERAL RESEARCH AND EXPLORATION (MTA Dergisi)
Article Details
Assessment of crustal thinning and tectonic stress distribution of Gülbahçe fault zone and its surroundings (İzmir, West Türkiye) using gravity and magnetic anomalies
Gülbahçe Fault Zone (GFZ) is a significant tectonic structure and seismic source for İzmir city and its surroundings. The major earthquakes occurred at the surroundings of GFZ are 2005 Seferihisar, 2020 Samos Island-Aegean Sea and 2021 Seferihisar earthquakes. In this study, the crustal thinning and tectonic stress distribution of GFZ and its surroundings were analyzed by using the new gravity and magnetic data. The correspondence analysis was applied by appraising together the magnetic and free-air anomaly data. Moreover, the average density of the subsurface structure was calculated by applying the Parasnis method. The deviatoric stress calculation was executed and the change of the physical properties that controls the gravity and magnetic anomaly of the crustal structure of the GFZ and its surroundings from north to south was investigated. Therefore, the average density values, which were obtained from gravity anomalies, were computed as 2.59 gr/cm3 in the north of the study region and it decreased to 2.06, 1.8 and 1.49 gr/cm3 towards to the south. The freeair gravity anomaly values were between 0-70 mGal and the magnetic anomalies were between -450-150 nT. The deviatoric stress values were between -0.2-0.1 MPa.
Gökhan DEMİRELA, Mustafa Haydar TERZİ, Ahmet Fatih OSKAY
Indexed In · Volume 178 / December 2025
Pegmatites and alkali feldspar granites as sources of industrial K-feldspar: A study from Borucu, Aksaray, Central Türkiye
Authors:
Gökhan DEMİRELA, Mustafa Haydar TERZİ, Ahmet Fatih OSKAY
ABSTRACT
The Borucu (Aksaray) region, within the Central Anatolian Crystalline Complex, comprises a variety of rocks, including granite, alkali feldspar granite (AFG), pegmatite, and aplite dikes. The granite and AFG host some veins or lenses of pegmatites, with lengths reaching approximately 70 m in the N10-25W direction. The AFG and pegmatitic rocks are characterized by variable mineral assemblages, including K-feldspar (orthoclase), quartz, plagioclase, and to a lesser extent, biotite, garnet, and opaque minerals. Inner zones feature the mega-grained pegmatite, whereas outer zones consist of the coarse-grained K-feldspar and quartz pegmatite. In this study, integrated surface and vertical (trenching and drilling) exploration, mineralogy-petrography, geochemical, and magnetic separation analyses were employed to assess the industrial raw material potential of the AFG and pegmatites. The total alkali (Na2O+K2O) contents reach 15.56-16.82% for the mega-grained pegmatite, 8.07-9.76% in the coarse-grained pegmatite, and 9.20-9.66% in the AFG. However, the Fe2O3 contents (0.30-1.15%) constrain their industrial raw material quality. Magnetic separation improved the AFG material to second-quality ceramic industry standards. Despite Fe2O3 limitations, Borucu’s pegmatites and AFG represent usable industrial raw material resources.
Keywords:
Alkali Feldspar Granite, Pegmatite, K-Feldspar, Magnetic Separation.
Magnetic anomalies and geological signatures in the Black Sea: a comprehensive study of the east and west basins
Authors:
İlkin ÖZSÖZ, Eşref AYLAN, Ceyhan Ertan TOKER
ABSTRACT
This study investigates the origin of the Black Sea, focusing on the East and West Black Sea basins. Data such as Curie Point Depth values, heat flow, bathymetry, Moho depth, sediment thickness, and magnetic depth estimation were analyzed to explore the region’s geological features. Correlations between these parameters were assessed for each basin, shedding light on their tectonic history and the influence of volcanic rocks. Thinner sedimentary covers enhanced the detectability of rocks with higher magnetic properties, while the interiors showed lower magnetic anomalies due to younger sedimentary rocks. Edge detection techniques, like tilt angle and Local Wavenumber methods, improved magnetic data interpretation. The study computed Curie Point Depth and heat flow using 65 blocks, revealing greater depths in the Western Black Sea (up to 32 km) compared to the Eastern Black Sea (24-28 km). Two profiles (A-A’ and B-B’) were examined for further insights. Overall, this study provides valuable insights into the geological evolution of the Black Sea basins.
Keywords:
Curie Point Depth, Heat Flow, Tilt Derivative, Local Wavenumber, Correlation Plot.
Mona FAWZY, Mustafa BAYOUMI, Hassan SHAHIN, Bahaa EMAD, Abdel Hay EL SHAFEY, Marwa ABDEL-AZEEM, Ahmed ISMAIL, Asmaa EL-MOGHAZY, Mohamed DIAB
Indexed In · Volume 174 / August 2024
Economic heavy minerals in the stream sediments of wadi Shaàb, southern coast of the Red Sea, Egypt; characterization and upgrading for investigation of their potential recovery
Authors:
Mona FAWZY, Mustafa BAYOUMI, Hassan SHAHIN, Bahaa EMAD, Abdel Hay EL SHAFEY, Marwa ABDEL-AZEEM, Ahmed ISMAIL, Asmaa EL-MOGHAZY, Mohamed DIAB
ABSTRACT
The southern coast of the Red Sea is one of the most promising areas for the occurrence of economic minerals. Therefore, studying the characterization and evaluation of these minerals in the Wadi Shaàb Quaternary sediments and investigating their ability to concentrate and physically separate using economical and ecofriendly techniques is the main goal of this work. The results showed that the representative sample contains an average of 0.06% ilmenite, 0.08% zircon, 0.07% rutile, 0.07% leucoxene, 0.008% cassiterite, 0.004% xenotime, 0.0004% monazite, 0.022% almandine garnet, and 0.46% magnetite. The recovery of economic heavy minerals was applied using a combination of wet-gravity technique via shaking table and magnetic separation using high intensity magnetic separator. The results demonstrated the success of gravity separation in raising the grade from 7.63% to 45.03% in a yield of 13.74% out of the original sample, and also valuable metallurgical recoveries that higher than 89% for tabling multi-stages (rougher and scavenging) was obtained. Concentrated mineral fractions of magnetite, ilmenite, almandine, heavy silicates, and the nonmagnetic fraction bearing zircon and rutile were obtained using a high intensity magnetic separator at different ampere range.
Keywords:
Heavy Minerals, Red Sea Coast, Gravity Concentration, Magnetic Separation, Potential Recovery, Material Balance.
Investigation of thermal transformation of composite material obtained from granite and recrystallized limestone natural stone wastes.
Authors:
Gökhan EROL, Devrim PEKDEMİR
ABSTRACT
In this study, the usability of granite (magmatic) and recrystallized limestone (metamorphic) natural stone wastes as alternative raw materials in ceramic tile production was investigated. Based on the CaO, SiO2, and Al2O3 compounds found in waste powders, mixtures containing 65% granite and 35% recrystallized limestone (by mass) were prepared to obtain the ceramic phases of gehlenite, wollastonite and anorthite as a result of thermal transformation. The grain size of both raw materials is -149 μm (d90 = 110.957 μm). The first series samples are called natural building stone (DYT), and the second series samples, in which wood chips of 2% (by mass) -1 mm grain size are added to obtain porous material, are called natural building stone - porous (DYT-G). The samples belonging to both series was applied heat treatment at 1,160°C. Phase analysis of samples obtained after heat treatment was measured by X-Ray Diffraction (XRD) and Scanning Electron Microscope (SEM-EDS) methods, and sintering properties were measured using water absorption coefficient, flexural strength, modulus of elasticity, density-porosity and color measurement tests. Gehlenite and wollastonite phases were detected in the heat treated samples, but no anorthite phase was observed. According to the test results, it was determined that the flexural strength (22.64 MPa) of the DYT marked sample was in accordance with the ceramic tile standards. In the DYT-G example, despite the decreasing unit volume mass value, it was determined that the bending strength (16.50 MPa) was in the range of ceramic tile strength values.
https://doi.org/10.19111/bulletinofmre.1081187
Güzin Gülsev UYAR AKSOY, Cemalettin Okay AKSOY, Hasan Eray YAMAN
Indexed In · Volume 169 / 2022
Estimation of blast vibrations by numerical modelling and signal analysis
Authors:
Güzin Gülsev UYAR AKSOY, Cemalettin Okay AKSOY, Hasan Eray YAMAN
ABSTRACT
Seismic waves carry all the geological and geotechnical characteristics of the units they pass along the route they travel on. Therefore, seismic waves can be called the signature of the route it passes through. If the blasting point is considered as source, blast-induced seismic waves measured at a certain distance from the source can be revealed and this form can be integrated into the dynamic numerical model, the effects that will occur at any point of the model can be predicted. In this study, seismic waves induced from single-hole blast and a group blast consisting of holes with the same characteristics as a pilot blast hole were obtained using particle velocity data obtained from seismographs at certain distances and integrated into the numerical model. The data processing technique used is to estimate the theoretical group blasting data from the pilot data according to the linear superposition principle and compare with the real group blasting data to determine the nonlinear behavior effect on the blast source from the difference. When the results were examined, it was observed that the numerical model results and field measurements coincided. The results of this study will make a significant contribution to the science of rock engineering.
https://doi.org/10.19111/bulletinofmre.1066943
Ayça ÇIRMIK, Ufuk AYDIN, Oya ANKAYA PAMUKÇU, Fikret DOĞRU
Indexed In · Volume 169 / 2022
Analysis of the stress distribution of North Anatolian Fault Zone for the part between Amasya-Tokat cities
Authors:
Ayça ÇIRMIK, Ufuk AYDIN, Oya ANKAYA PAMUKÇU, Fikret DOĞRU
ABSTRACT
Tectonic forces formed in the continental crust, cause permanent changes in stress, compression and deformation. The amplitudes of earthquake waves vary with the stress/strain distribution in the crust. In this study, the change of stress / strain and regional absorption coefficient, which is effective in tectonic forces caused by elastic deformation energy accumulating in the brittle crust over time, was investigated. The study area is the middle part of the North Anatolian Fault Zone and the area formed by Ezinepazarı fault zone and Merzifon fault zone. In this area, Coulomb stress analysis was carried out by using the focal mechanism solution values of the earthquake that occurred in Yoldere-Erbaa, Tokat on October 9, 2015 (ML=5.1). In order to examine the deformation caused by this earthquake in and around the study area, Global Navigation Satellite System (GNSS) data were evaluated and the velocities of these stations were calculated using GNSS data of these stations for the years 2013-2014-2015-2016. Also, regional absorption coefficients were determined by using earthquake data. As a result, Coulomb stress analysis results, velocity values distribution obtained from GNSS data and absorption findings obtained from seismological study were evaluated together.
https://doi.org/10.19111/bulletinofmre.1022323