Volume 156 · 2018 · 15 ARTICLES
All Articles In This Issue
01
Indexed In · Volume 156 / 2018
Holocene activity of the Orhaneli Fault based on palaoseismological data, Bursa, NW Anatolia
Authors: ABSTRACTOrhaneli Fault is 30 km long, right-lateral strike-slip fault with dominant reverse component located in the Biga Peninsula. This fault controls the southern margin of the Quaternary Orhaneli Basin. Additionally, it cuts the metamorphic rocks of the Tavşanlı Zone, Cretaceous ophiolitic units and Neogene/Quaternary sediments, and can be easily recognized on aerial photographs and in the fi eld due to linearity and fault scarps. Elongated ridges, offset valleys and fault saddles observed along the fault are important geomorphological features indicating fault activity. This study presents the results of the fi rst palaeoseismological study on the Orhaneli Fault. Two trenches were excavated along the fault. These trenches, named Serçeler and Kusumlar, exhibited that metamorphic rocks of the Tavşanlı Zone were thrust onto Quaternary sediments by the fault. The study encountered evidences of four large earthquakes accompanied by surface rupture in Quaternary. The results of Serçeler trench indicated the older earthquake occurred between 22,000±3,200 BC and 6,600±800 BC, and the most recent earthquake occurred before 770-415 BC. The Kusumlar trench data showed that the older earthquake occurred between 6,660 BC and 3,085 BC, and the most recent event in the period after 650 AD. Any interpretation could not be made about the recurrence period between palaeoearthquakes. In this study, Holocene activity on the Orhaneli Fault was proven. If this fault, with 30 km total length comprising two segments, ruptured as a single piece, it has the potential to
produce an earthquake with Mw=6.9.
http://dx.doi.org/10.19111/bulletinofmre.413248
Keywords:
02
Indexed In · Volume 156 / 2018
The neotectonics of NE Gaziantep: The Bozova and Halfeti strike-slip faults and their relationships with blind thrusts, Turkey
Authors: ABSTRACTIn the northeast of Gaziantep, east-west trending thrusts, northeast-southwest trending left lateral strike-slip faults and northwest-southeast right lateral strike-slip faults are located. They are typical features of the neotectonics of southeast Anatolia, Turkey. Detailed mapping of these structures and structural data obtained from fi eld studies indicate that east-west trending thrust faults and related fault propagation folds is post-Pliocene. The strike-slip faults that cut these structures should be younger than the thrust fault. On the other hand, the recent seismic activity in the southeast Anatolia (2011.10.23 – M=7.3 Van; 2012.06.14 – ML=5.5 Şırnak-Silopi earthquakes) shows that north-south compression is taken by both thrusting and strike-slip faulting.
http://dx.doi.org/ 10.19111/bulletinofmre.401216
Keywords:
03
Indexed In · Volume 156 / 2018
Neotectonic and morphotectonic characteristics of the Elmali basin and near vicinities
Authors: ABSTRACTElmalı Basin, which consists of the Elmalı county and some villages, approximately 120 km far from Antalya city, is one of the recent depositional areas in the extensional neotectonic region of southwestern Turkey. The basin provides signifi cant data for the understanding of the geological evolution to record from the basement to recent depositional units. For this reason, these kinds of structures are used to determine the deformations phases for the evolutionary history of basin formation. In the content of the study, following applications have been investigated: (a) mapping of the area and structures in 1/25.000 scale, (b) information about deformation and tectonic activity along the basin margin faults, (c) the distribution of peak ground acceleration (PGA) in case of an earthquake with 6.5 magnitude and (d) morphometric analyzes of the basin to understand the tectonic uplift by using the digital elevation model. The new results combined with existing data imply that the Elmalı Basin has a number of deformation structures and active faults on both western and eastern sites of the basin. Depending on the morphometric indices, western side of the basin created higher uplift ratio compared with the eastern side of the basin.
http://dx.doi.org/10.19111/bulletinofmre.399090
Keywords:
04
Indexed In · Volume 156 / 2018
Syn-sedimentary deformation structures in the Early Miocene lacustrine deposits, the basal limestone unit, Bigadiç basin (Balıkesir, Turkey)
Authors: ABSTRACTIn the Western Anatolian region, NE-SW, E-W directional basins were developed which were limited to the extension-related faults beginning in the late Oligocene to early Miocene. The fi llings of these basins consist of fl uvial – lacustrine deposits containing volcanic and volcaniclastic intercalations. These deposits include intensive local unconformities and soft sediment deformation structures. The fi lling of the Bigadiç Neogene Basin which is one of these basins, constitute base limestone unit, lower tuff unit, lower borate unit, upper tuff unit and upper borate unit. The base limestone unit composed of claystone, marl, limestone, dolomitic limestone facies was deposited in the deep lacustrine environment. The soft sediment deformation structures were defi ned in the base limestone unit, which outcroped in the south of Bigadiç. These are: slumps, rock falls, chaotic structures, clastic dykes, synsedimentary faults and breccia limestone. Deformation mechanisms are related essentially to the increase of slopes of layers, liquidization and fl uidization. In the study area; regional tectonics, sedimentological data, and deformation structures are evaluated together, it is concluded that these structures are formed by tectonic and seismic (earthquakes related to tectonic origin and syndepositional magmatic activities).
http://dx.doi.org/10.19111/bulletinofmre.378545
Keywords:
05
Indexed In · Volume 156 / 2018
The effect of submarine thermal springs of Doğanbey Cape (Seferihisar - İzmir) on foraminifer, ostracod and mollusc assemblages
Authors: ABSTRACTThe aim of this study was to fi gure out the effects of the submarine hot water springs located on the coast of Doğanbey Cape (north of Kuşadası Bay) on various micro- and macrofaunal assemblages living around these springs. Young sediment samples were collected from different depths at 15 stations. The benthic foraminifer, ostracod and mollusc faunas were investigated. 35 genera and 61 species of benthic foraminifers, 16 genera and 20 species of ostracods and 14 genera and 15 species of molluscs were identifi ed. Typical Aeegan foraminifer fauna was found to be dominant. Besides, individuals with colored tests or abnormal morphology, as well as alien species, which are frequently observed on the Aegean coasts were also observed in the study area. The foraminifer, ostracod and mollusc species also constituted typical Aegean fauna. It is known that the ecological conditions experienced of the Amphistegina lobifera Larsen individuals in typical Aegean benthic foraminifer assemblage have an effect on the abundance distribution. Ideal conditions for Amphistegina lobifera Larsen was found to be 18.00-32.00 m depth range and 19-20oC temperatures. CTD conductivity values gradually increased near to the hot water spring but a decrease in the number of individuals were observed. Chemical analyzes in sediment samples were performed with X-Ray Fluorescence Analysis Spectrometer (WDXRF). Heavy metal ingredients (Cr, Mn, Co, Ni, Cu, Zn and Pb) of the sediments were evaluated, concentrations were recorded as Cr>Ni>Mn in samples DB1-DB6 and also in DB15; Mn>Cr>Ni in DB8-DB11 and DB13-DB14; Cr>Mn>Ni in DB7 and in DB12. The radioactive elements U and Th were found to be high in DB9, DB10 and DB11. The chemical and radioactive properties of the sediments were observed to affect the tests of benthic foraminifers, where as no such effect was found on ostracod and mollusc tests.
http://dx.doi.org/10.19111/bulletinofmre.363329
Keywords:
06
Indexed In · Volume 156 / 2018
Palynology of the Kılçak formation (Early Miocene) from Central Anatolia: Implications for palaeoclimate and palaeoenvironment
Authors: ABSTRACTThe palynological analysis of the early Miocene successions of the Kılçak formation (Central Anatoia, Turkey) was carried out in order to reconstruct the palaeovegetation. The pollen spectra indicate a fl ora dominated by Pinus, co-dominance of Cupressaceae in one of the investigated successions, and lower percentages of trees such as Taxodioideae within Cupressaceae, Quercus deciduous type, Carya, Carpinus, Ulmus, Engelhardioideae, Salix, Alnus and Juglans. Herbs are represented by minor amounts of Poaceae, Amaranthaceae/Chenopodiaceae and Asteraceae. This flora indicates the presence of a Taxodium topogenous mire with a nearby riparian vegetation and broadleaved deciduous mixed forests developed in the surrounding distant mountainous areas. δ13C analysis shows that the vegetation was dominated by C3 plants. The Kılçak palynoflora reflects a humid, warm-temperate climate being compatible with the global warm conditions maintained during the early Miocene
http://dx.doi.org/10.19111/bulletinofmre.395784
Keywords:
07
Indexed In · Volume 156 / 2018
Mineralogical findings from manganese deposits in the Artova Ophiolite Complex, Derbent-Eymir area, Yozgat, Turkey
Authors: ABSTRACTThe Artova Ophiolitic Complex (AOC), which formed in association with Alpine Ophiolites, is exposed in the NE part of central Anatolia, in the interior of the central Black Sea region and within the borders of Çorum and Yozgat. The Derbent-Eymir manganese- oxide deposit under investigation occurs within this ophiolitic complex. The mineral association in Derbent ore is composed chiefly of pyrolusite, manganite and lesser amounts of ramsdellite, magnetite and goethite. Calcite is the main gangue mineral. The mineral association in Eymir ore is represented by pyrolusite, braunite, neltnerite, jacobsite, psilomelane and trace amount of limonite accompanied by some gangue minerals such as quartz and calcite. Electron microprobe analysis was carried out on pyrolusite, braunite and psilomelane minerals. While pyrolusite from Eymir has higher Si, Al, Mn and Ca, pyrolusite from the Derbent ore has lower Fe, K and Ba contents. Pyrolusite in the Eymir ore has higher Si, Al, Mn and Ca (10.28-7.06; 3.19-1.28; 87.98-81.88; 2.38-1.97 respectively) and lower Fe, K and Ba (0.31-0.16; 0.02-0.00; 0.07-0.00 respectively) contents in comparison to pyrolusite in the Derbent ore. Element variations in core-rim zones of spherical pyrolusites and manganite crystals elongated towards the gangue are quite noticeable. Both Eymir and Derbent ore deposits are low-temperature hydrothermal deposits. Geochemical variations recorded in various manganese minerals are found to be strongly dependent on the changes in pH and temperature of the ore-forming solution and distance to the spreading center.
http://dx.doi.org/10.19111/bulletinofmre.334245
Keywords:
08
Indexed In · Volume 156 / 2018
Petrographic and palynological investigations of Sinanpaşa (Afyon) Miocene coals
Authors: ABSTRACTIn this study, petrographical and palynological analyses of coal samples from two regions (the Kırka region in the south, and the Karacaören region in the north) of the Sinanpaşa (Afyon) Neogene basin were performed. The coal-bearing Neogene sediments indicate the occurrence of fi ve facies: paleosol, matrix-supported conglomerate, coal-bearing mudstone, sandstone-claystone and laminated mudstones. Coal layers are mainly within coal-bearing mudstone facies. In addition, there are various types of coalifi ed materials in matrix-supported conglomerate and sandstone-claystone facies. Based on coal petrography, an interpretation of the coal-forming environment was made. The investigated coals mainly contain a huminite maceral group. From the refl ection values (Rmax), these coals can be classifi ed as sub-bituminous in rank, and as being deposited in swamp zones associated with limnic environments. The palynological data indicates that all studied coal-bearing units are of Mid-Miocene age. On the other hand, based on MAT, CMT, WMT and MAP parameters, it can be stated that at that time climatic conditions changed seasonally in the study area. Humid climatic conditions prevailed during the period when the peat was formed, then later transformed into the coal layers examined in this manuscript.
http://dx.doi.org/10.19111/bulletinofmre.363345
Keywords:
09
Indexed In · Volume 156 / 2018
Separation of geochemical anomalies using inverse distant weighting (IDW) and concentration-area (C-A) fractal modeling based on stream sediments data in Janja Region, SE Iran
Authors: ABSTRACTIn this study, the Inverse Distant Weighting (IDW) and the Concentration –area (C-A) fractal methods were used for identifi cations of geochemical anomalies in Janja region, SE Iran. Eight elements (Au, Cu, Mn, Zn, Fe, As, Mo, and Pb) from 300 stream sediment samples were used. The studied area was gridded by 250 m×250 m cells. Estimation of unsampled locations were carried out by inverse distant squared weighting (IDWS) method. Geochemical maps were generated. Log- log plots of cumulative frequency of elemental concentrations versus related areas were constructed. Threshold values were obtained by fi nding break points in the log-log plots. There were four geochemical populations for As, Fe, Mo, Pb and Zn and fi ve geochemical populations for Au, Cu, and Mn. The resulted geochemical anomaly maps obtained from fractal modelling showed that Anomalies of Zn, Mo, Mn, Fe, Cu and As located in southeastern part of study area. There was a good correlation between faults and elementals anomalies. It can be concluded that mineralization occurred along the faults. There was a correlation between anomalies and sedimentary rocks (alluvium and recent alluvium sediments) in SE part of study area. Gold anomalies were located in the NW parts of the studied area. There was a strong relationship between the location of Au anomalies and fault systems in the NW parts of the studied area. Iron concentrations were sporadic and correspond to the sedimentary volcanic rock and turbidites.
http://dx.doi.org/ 10.19076/mta.401236
Keywords:
10
Indexed In · Volume 156 / 2018
Use of Moran’s I and robust statistics to separate geochemical anomalies in Jiurui area (Southeast China)
Authors: ABSTRACTSeparation of geochemical anomalies from background plays an important role in the study of exploration geochemistry. The limitations of commonly used methods are not taken into account spatial correlation, variability and the unsatisfactory of the statistical assumption of the normality of geochemical data. For solving these limitations, an indirect method for the separation of geochemical anomalies is proposed based on anomaly separation of local Moran’s Ii values using robust statistics in this study. The experiment was carried out using 1481 samples collected from Jiurui copper prospect (southeast China). The steps for the anomaly separation are (i) spatial association and variability were fi rst analyzied by means of Moran scatterplots at six spatial scales (2, 4, 6, 8, 10 and 12 km) using both raw data and Box-Cox transformed data; (ii) local Moran’s Ii was used to measure spatial autocorrelationat these six local scales; (iii) anomalous separation was fi nally performed using the MEDIAN ± 1.5*IQR (IQR: interquartile range) rule on local Moran’s Ii values. The results show that geochemical anomalies are mostly concentrated around known ore-deposits, according the objective reality and a strong correlation with known ore-deposits in Jiurui copper prospect.
http://dx.doi.org/ 10.19111/bulletinofmre.351376
Keywords:
11
Indexed In · Volume 156 / 2018
Assessment of souil liquefaction using the energy approach
Authors: ABSTRACTDamage to structures during earthquakes may be fully or partly caused by soil liquefaction, which has been the subject of extensive research for several decades. Liquefaction susceptibility of a sandy deposit is performed by comparing the resistance of a soil to liquefaction (i.e., capacity) to the load imparted by an earthquake (i.e., demand). In this regard, the stress-based method of liquefaction assessment is by far the most popular. It involves uncertainties mostly related to the computation of the maximum horizontal ground acceleration (amax) at bedrock. A site response analysis or a simplifi ed assumption is necessary to determine the amax on the ground level as well. Developing from the stress-based approach, the strain-based approach has also similar constraints. There exist laboratory techniques such as torsional shear to determine the capacity of a sandy soil in terms of liquefaction energy per unit volume. Likewise, the energy of a strong motion record can be set by employing simple physics principles. For this, a velocity time history and the unit mass of the soil are employed to compute the demand of any strong motion record. The scope of this investigation is to illustrate the usability of the energy-based method for the evaluation of soil liquefaction. The defi ciencies of the stress- and strain-based approaches are outlined and the advantages of the energybased approach are discussed.
http://dx.doi.org/10.19111/bulletinofmre.351257
Keywords:
12
Indexed In · Volume 156 / 2018
Determination of predominant site period of loose terestrial units (Caliche) by microtremor measurements
Authors: ABSTRACTThe caliche profi les that have been observed in arid-semi arid climate regions can be described as terrestrial formations which are vertical succession and composed predominantly of calcium carbonate. At the top of the caliche profi le, there is hard pan leyer as a weak rock and soft pan layer characterized by loose soil is existed. Caliche is formed by the displacement and/or cementation of soil, rock, and weathered material, and is usually found in unsaturated zones. In the study area, consist of caliche units located in Adana. It is noteworthy that the caliches of Quaternary is widely crop out throughout the region, exhibited a fl at topography in the region locate at this unit. The paleosolic deposits in the Adana Basin, which is characterized by climate oscillations in the Pleistocene and surface waters rich in carbonate, following draining, capillarity and weathering, initially formed as a result of sedimentological and followed by pedological processes. Adana is located in the I. and II. degree seismic zone, where many earthquakes have been observed in historical and instrumental periods. It was found that the greatest structural damage sustained by the earthquakes that occurred in Adana especially in 1998, was seen in the buildings located on caliche ; it is believed that the damage caused to the buildings located on chalice can be attributed to the of morphologically distinct layers or horizons. This study determines the sediment amplifi cation characteristics and horizontal to vertical spectral ratio (H/V) within the borders. Accordingly, to demonstrate H/V between the hard pan and the soft pan horizon of the caliche, 24 microtremor measurements were performed on locatio ns with soft pan, on locations with no hard pan, and on locations where the profi le directly begins with the soft pan.
http://dx.doi.org/10.19111/bulletinofmre.348301
Keywords:
13
Indexed In · Volume 156 / 2018
The Hydrogeological investigation of Plajköy spring (Elazığ)
Authors: ABSTRACTPlajköy spring discharges at the close locations to the SE shore of Lake Hazar. Lake Hazar is a tectonic Lake in Elazığ city. Plajköy spring is a fault spring that is mainly recharging from the volcanites, dikes and blocky volcanosedimentary units of Middle Eocene Maden Complex. These units have gained secondary permeability and porosity related with the active tectonics that is effective in the studied area. The present catchment system of the spring could not collect the springs and leaks discharging from different points around the system. The discharge of the catchment is measured by specifi c volume method while the other springs’ and leaks’ is measured by using triangular weir. Before the discharge measurement of the leaks and the springs, they have been directed to a channel. The discharge of the present catchment system and the leaks have measured twice in a month during one year period beginning from October of 2012 to November of 2013. The discharge coeffi cient of the spring is calculated 1.33*10-3 day-1. Discharge coeffi cient of the spring depends on the geometry and intensity of the active fracture systems in the region. Calculated discharge coeffi cient indicates that the spring discharge is related with the narrow fi ssures, fractures and pores. The total volume of discharged groundwater in the real regime of the Plajköy spring is calculated as 52* 103 m3 during the period from 31st of March, 2013 to the 13rd of October, 2013 by Maillet formula. The spring water is Ca- Mg- HCO3 type water related with the chemical analyses. The chemical and microbiological analyses of the spring water are correlated with the drinking water standarts of Turkey TS 266 (TSE, 2005) and World Health Organization (2004), and it is seen that the spring water is suitable for drinking. The Plajköy spring will be used more effi ciently without exposed to pollution by the new catchment plan and protection zone map that are consequently proposed in the present study.
http://dx.doi.org/10.19111/bulletinofmre.376767
Keywords:
14
Indexed In · Volume 156 / 2018
Characterization and dewatering of borax clayey tailings by mono- and dual-flocculants systems
Authors: ABSTRACTThis study includes dewatering of Kırka Borax Concentrator tailings by fl occulation with mono- and dual-fl occulants systems. Four polyacrylamide (PAM)-typed anionic and a poly diallyl-dimethylammonium chloride (PolyDADMAC)-typed cationic polymers were used as fl occulants in monoand dual-fl occulants systems to fl occulate tailings. Tailings slurry sample used in the experiments were taken from the discharge point of Kırka Borax Concentrator. Prior to the fl occulation tests, physical, chemical and mineralogical analysis were carried out to characterize the tailings slurry. Results reveal that while tailings solid consists mainly of dolomite and montmorillonite with some unrecoverable boron mineral fi nes and very minor amount of calcite and quartz, tailings water is typical with the content of quite high dissolved carbonate and borax with a pH of 9.4. Flocculation tests were performed in one liter graduated cylinder at inherent pH of the tailings slurry sample. Settling rate and turbidity of overfl ow was measured as important factors for evaluating the fl occulation performance of different fl occulants. The tailings slurry as received showed a very low settling behavior due to the clay content and high percentage of fi ne particles. Flocculation of tailings with anionic fl occulants accelerated the settling rate of particles without providing a clear supernatant. But, dual-fl occulants system, in which anionic and cationic type polymeric fl occulants were used, was able to provide a clear supernatant at relatively higher settling rates.
http://dx.doi.org/10.19111/bulletinofmre.336392
Keywords:
15
Indexed In · Volume 156 / 2018
The Naşa intrusion (Western Anatolia) and its tectonic implication: A joint analyses of gravity and earthquake catalog data
Authors: ABSTRACTThe gravity data gathered in and around the Simav Graben in Western Anatolia were reprocessed and reinterpreted by using the standard deviation fi lter and the Euler deconvolution. The joint evaluation of results from the interpretation of gravity data and seismological studies indicates the presence of new intrusive structures in the vicinity of Simav. The intrusion is located in the eastern margin of the graben and has a thickness of 12-15 km at 2.5-3 km depth below the surface. Numerous earthquakes recorded in the eastern part of the graben are associated with this intrusion. Besides, the multidimensional modelling study of the gravity data allowed us to display the Simav Graben, the fold of the Simav Fault, the intrusion named as Naşa, and the epicenters of earthquake within the same tectonic frame. All tectonic structures were marked on the three dimensional relief model.
http://dx.doi.org/10.19111/bulletinofmre.410597
Keywords:
No articles match your search.