İşleminiz gerçekleştirilirken lütfen bekleyiniz.

Please wait


Makale Detayları

[Türkçe .pdf]
USABILITY OF PCF-ASH AS LIGHTWEIGHT AGGREGATE IN FOAM CONCRETE
Başlık: USABILITY OF PCF-ASH AS LIGHTWEIGHT AGGREGATE IN FOAM CONCRETE
Yazarlar: Metin DAVRAZ, Şemsettin KıLıNçARSLAN
Anahtar Kelimeler: Foam concrete, lightweight aggregate, PCF ash, compressive strength, thermal conductivity
Özet:

Foam concretes with low dry density can be produced with aggregate or without aggregate. However, if the aggregate-mineral admixture isn't used in the foam concrete, there may be a lot of problems such as precipitation in fresh condition, high- drying shrinkage in case of hardening, thermal shrinkage and high unit cost. In this study, the possibility of using PCF ash as lightweight aggregate in the production of foam concrete was investigated. Waste-PCF ash is emerging from the pulverized coal furnace about 10 tons/day in a textile factory located in the vicinity of Dinar (Afyonkarahisar). The chemical properties, particle size distribution and grain densities of PCF-ash were determined. Foam concrete with a dry density of 450 kg/m3 at a cement dosage of 250 kg/m3 and w/c:0.65 was produced after the aggregate analysis. The PCF-ash which is used in foam concrete mix is between 0 and 200 kg/m3. 100 mm cube and 300x300x50 mm prism samples were prepared with this foam concrete. The compressive strengths of the cube samples and the thermal conductivity coefficient of the prism samples were tested at the 28th day. The average compressive strength of foam concrete samples with a density of 452 kg/m3 was determined as 1.07 MPa and the thermal conductivity coefficient was determined as 0.097 W/mK. As a result, it has been determined that PCF- ash as lightweight aggregate can be successfully used in production of precast element and light floor-screed.

https://doi.org/10.19111/bulletinofmre.545562

 

Details

[English .pdf]
USABILITY OF PCF-ASH AS LIGHTWEIGHT AGGREGATE IN FOAM CONCRETE
Title: USABILITY OF PCF-ASH AS LIGHTWEIGHT AGGREGATE IN FOAM CONCRETE
Authors: Metin DAVRAZ, Şemsettin KıLıNçARSLAN
Keywords: Foam concrete, lightweight aggregate, PCF ash, compressive strength, thermal conductivity
Abstract:

Foam concretes with low dry density can be produced with aggregate or without aggregate. However, if the aggregate-mineral admixture isn't used in the foam concrete, there may be a lot of problems such as precipitation in fresh condition, high- drying shrinkage in case of hardening, thermal shrinkage and high unit cost. In this study, the possibility of using PCF ash as lightweight aggregate in the production of foam concrete was investigated. Waste-PCF ash is emerging from the pulverized coal furnace about 10 tons/day in a textile factory located in the vicinity of Dinar (Afyonkarahisar). The chemical properties, particle size distribution and grain densities of PCF-ash were determined. Foam concrete with a dry density of 450 kg/m3 at a cement dosage of 250 kg/m3 and w/c:0.65 was produced after the aggregate analysis. The PCF-ash which is used in foam concrete mix is between 0 and 200 kg/m3. 100 mm cube and 300x300x50 mm prism samples were prepared with this foam concrete. The compressive strengths of the cube samples and the thermal conductivity coefficient of the prism samples were tested at the 28th day. The average compressive strength of foam concrete samples with a density of 452 kg/m3 was determined as 1.07 MPa and the thermal conductivity coefficient was determined as 0.097 W/mK. As a result, it has been determined that PCF- ash as lightweight aggregate can be successfully used in production of precast element and light floor-screed.



 
MTA Bilgi İşlem Koordinatörlüğü - 2013/2019